 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HN62448N Series 524288-word x 16-bit/1048576-word x 8-bit CMOS Mask Programmable ROM ADE-203-385B (Z) Rev. 2.0 Oct. 21, 1996 Description The Hitachi HN62448N is a 8-Mbit CMOS mask-programmable ROM organized either as 524288-words by 16-bits or as 1048576-words by 8-bits. And a high speed access of 100/120 ns is the most suitable to the system using a high speed microcomputer by 16 bits. Features * Single 5 V power supply * Access time: Normal access time: 100/120 ns (max) Page access time: 40/50 ns (max) * Low power dissipation Active: 300 mW (typ) Standby: 5 W (typ) * Byte-wide or word-wide data organization with BHE * 4-word page access mode * Three-state data output for wired or-tying * Directly TTL compatible (All input and output) Ordering Information Type No. HN62448NP-10 HN62448NP-12 HN62448NFB-10 HN62448NFB-12 HN62448NTT-10 HN62448NTT-12 Access time 100 ns 120 ns 100 ns 120 ns 100 ns 120 ns Package 600mil 42-pin plastic DIP (DP-42) 44-pin plastic SOP (FP-44D) 44-pin plastic TSOP II (TTP-44D) HN62448N Series Pin Arrangement HN62448NP Series A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE D0 D8 D1 D9 D2 D10 D3 D11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 (Top view) HN62448NTT Series NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE D0 D8 D1 D9 D2 D10 D3 D11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 (Top view) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC NC A8 A9 A10 A11 A12 A13 A14 A15 A16 BHE VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 NC A8 A9 A10 A11 A12 A13 A14 A15 A16 BHE VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE D0 D8 D1 D9 D2 D10 D3 D11 HN62448NFB Series 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 (Top view) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC NC A8 A9 A10 A11 A12 A13 A14 A15 A16 BHE VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC 2 HN62448N Series Pin Description Pin name A0 to A18 D0 to D14 D15/A-1 OE CE BHE VCC VSS NC Function Address input Data output Data output/address input Output enable Chip enable Byte/word selection Power supply Ground No connection Block Diagram A0 to A15 Address buffer A16 to A18 X decoder Memory array Y decoder Y gates (A0, A1) (A-1) *1 Page decoder Hex / byte BHE OE 3-state output buffer CE BHE = VIH : 16-bit (D15 to D0) BHE = VIL : 8-bit (D7 to D0) *2 Note: 1. A-1 is least significant address. 2. When BHE is `low', D14 to D8 goes the high impedance state. D0 to D15/(D7) 3 HN62448N Series Absolute Maximum Ratings Parameter Supply voltage All input and output voltage Operating temperature range Storage temperature range Temperature under bias Note: 1. With respect to V SS . Symbol VCC Vin, Vout Topr Tstg Tbias Value -0.3 to +7.0 -0.3 to VCC +0.3 0 to 70 -55 to +125 -20 to +85 Unit V V C C C Note 1 1 Recommended DC Operating Conditions (Ta = 0 to +70C) Parameter Supply voltage Symbol VCC VSS Input voltage VIH VIL Min 4.5 0 2.2 -0.3 Typ 5.0 0 -- -- Max 5.5 0 VCC + 0.3 0.8 Unit V V V V DC Characteristics (VCC = 5 V 10%, VSS = 0 V, Ta = 0 to +70C) Parameter Supply current Active Standby Standby Input leakage current Output leakage current Output voltage Symbol I CC I SB1 I SB2 |IIL| |IOL | VOH VOL Min -- -- -- -- -- 2.4 -- Max Unit A mA A A V V Test conditions VCC = 5.5 V, IDOUT = 0 mA, tRC = 100/120 ns VCC = 5.5 V, CE VCC -0.2 V VCC = 5.5 V, CE 2.2 V Vin = 0 to VCC CE = 2.2 V, VOUT = 0 to VCC I OH = -205 A I OL = 1.6 mA 120/100 mA 30 3 10 10 -- 0.4 Capacitance (VCC = 5 V 10%, VSS = 0 V, Ta = 25C, Vin = 0 V, f = 1 MHz) Parameter Input capacitance* 1 1 Symbol Cin Cout Min -- -- Max 15 15 Unit pF pF Output capacitance* Note: 1. This parameter is periodically sampled and not 100% tested. 4 HN62448N Series AC Characteristics (VCC = 5 V 10%, VSS = 0 V, Ta = 0 to + 70C) Test Condition * * * * Output load: 1TTL gate + C L = 100 pF (including scope & jig) Input pulse levels: 0.45 to 2.8 V Input and output timing reference levels: 1.5V Input rise and fall time: 5 ns Read Cycle HN62448N-10 Parameter Read cycle time Page read cycle time Address access time Page address access time CE access time OE access time BHE access time Output hold time from address change Output hold time from CE Output hold time from OE Output hold time from BHE CE to output in high-Z OE to output in high-Z BHE to output in high-Z CE to output in low-Z OE to output in low-Z BHE to output in low-Z Symbol t RC t PC t AA t PA t ACE t OE t BHE t DHA t DHC t DHO t DHB t CHZ t OHZ t BHZ t CLZ t OLZ t BLZ Min 100 40 -- -- -- -- -- 0 0 0 0 -- -- -- 5 5 5 Max -- -- 100 40 100 40 100 -- -- -- -- 40 40 40 -- -- -- HN62448N-12 Min 120 50 -- -- -- -- -- 0 0 0 0 -- -- -- 5 5 5 Max -- -- 120 50 120 50 120 -- -- -- -- 40 40 40 -- -- -- Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 1 1 1 4 4 2 2 2 3 3 3 Note 5 HN62448N Series Note: 1. t CHZ, tOHZ and t BHZ are defined as the time at which the output achieves the open circuit conditions and are not referred to output voltage levels. 2. t DHA , t DHC, t DHO: Determined by faster. 3. t AA , t ACE, tOE: Determined by slower. 4. t CLZ, tOLZ : Determined by slower. 5. CE and OE are enable A18 to A0 are Valid. 6. D15/A-1 pin is in the output state when BHE is high, CE and OE are enable. Therefore, the input signals of opposite phase to the output must not be applied to them. 7. CE and OE are enable. 8. This device is used ATD (Address Transient Detecter). Therefore, transfer either CE or address (A2 to A18) after power up to 4.5 V. Timing Waveforms Word Mode (BHE = `VIH') or Byte Mode (BHE = `VIL ')* 2,3,4 tRC Address tAA CE tCLZ OE tOLZ Dout Valid data tOE tOHZ tDHO High-Z tACE tCHZ tDHC tDHA 6 HN62448N Series Word Mode, Byte Mode Switch*5, 6 High-Z tAA BHE tBHZ D7 to D0 tDHB D15 to D8 High-Z Valid data tBLZ Valid data tBHE Valid data tDHA High-Z Address Page Mode*7 A2 to A18 tRC A0, A1, (A-1) tPA tAA Dout Valid data tDHA tPA tDHA tPA tDHA tDHA tPC tPC tPC Valid data Valid data Valid data Power Up Sequence*8 4.5V VCC 0V CE t Address (A2 to A18) tAA Dout t 0ns Valid data Valid data tACE 7 HN62448N Series Package Dimensions HN62448NP Series (DP-42) Unit: mm 42 52.80 53.80 Max 22 15.0 Max 2.54 Min 5.06 Max 13.40 1 1.3 Max 1.20 21 15.24 0.51 Min 2.54 0.25 0.48 0.10 0.25 - 0.05 0 - 15 + 0.26 HN62448NFB Series (FP-44D) 28.50 28.70 Max 44 23 12.60 Unit: mm 3.00 Max 1 1.02 Max 22 0.17 0.05 16.04 0.30 1.72 0.19 0.10 0 - 10 0.80 0.20 0.40 0.10 1.27 0.10 0.12 M 8 HN62448N Series Package Dimensions (cont.) HN62448NTT Series (TTP-44D) 18.41 18.81 Max 44 23 Unit: mm 1 0.30 0.10 0.80 0.13 M 22 10.16 1.105 Max 1.20 Max 0.17 0.05 11.76 0.20 0 - 5 +0.03 -0.05 0.10 0.80 0.13 0.50 0.10 9 HN62448N Series When using this document, keep the following in mind: 1. This document may, wholly or partially, be subject to change without notice. 2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without Hitachi's permission. 3. Hitachi will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user's unit according to this document. 4. Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Hitachi's semiconductor products. Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein. 5. No license is granted by implication or otherwise under any patents or other rights of any third party or Hitachi, Ltd. 6. MEDICAL APPLICATIONS: Hitachi's products are not authorized for use in MEDICAL APPLICATIONS without the written consent of the appropriate officer of Hitachi's sales company. Such use includes, but is not limited to, use in life support systems. Buyers of Hitachi's products are requested to notify the relevant Hitachi sales offices when planning to use the products in MEDICAL APPLICATIONS. Hitachi, Ltd. Semiconductor & IC Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 For further information write to: Hitachi America, Ltd. Semiconductor & IC Div. 2000 Sierra Point Parkway Brisbane, CA. 94005-1835 USA Tel: 415-589-8300 Fax: 415-583-4207 Hitachi Europe GmbH Electronic Components Group Continental Europe Dornacher Strae 3 D-85622 Feldkirchen Munchen Tel: 089-9 91 80-0 Fax: 089-9 29 30 00 Hitachi Europe Ltd. Electronic Components Div. Northern Europe Headquarters Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA United Kingdom Tel: 0628-585000 Fax: 0628-778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 0104 Tel: 535-2100 Fax: 535-1533 Hitachi Asia (Hong Kong) Ltd. Unit 706, North Tower, World Finance Centre, Harbour City, Canton Road Tsim Sha Tsui, Kowloon Hong Kong Tel: 27359218 Fax: 27306071 10 HN62448N Series Revision Record Rev. 1.0 2.0 Date Contents of Modification Drawn by T. Kawajiri Approved by H. Moriuchi May. 23, 1995 Initial issue Oct. 21, 1996 AC Characteristics Input pulse levels: 0.45 to 2.4 V to 0.45 to 2.8 V 11 |
Price & Availability of HN62448NSERIES
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |